EIGRP

June 5, 2006 @ 9:59 am · Filed under CCIE Study

Group,
I have hub and spoke FR setup , I am trying to run EIGRP on that. Hub R2 shows adjaceny with both the spokes R1 and R3 but one of the spokes R1 giving following error.
R1# *Jun 5 14:03:28.263: EIGRP: Received UPDATE on Serial0/0/0 nbr 183.1.123.2 *Jun 5 14:03:28.263: AS 100, Flags 0×1, Seq 14/0 idbQ 0/0 *Jun 5 14:03:28.263: EIGRP: Neighbor(183.1.123.2) not yet found *Jun 5 14:03:28.807: EIGRP: Sending HELLO on Serial0/0/0 *Jun 5 14:03:28.807: AS 100, Flags 0×0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0 R1# *Jun 5 14:03:33.263: EIGRP: Received UPDATE on Serial0/0/0 nbr 183.1.123.2 *Jun 5 14:03:33.263: AS 100, Flags 0×1, Seq 14/0 idbQ 0/0 *Jun 5 14:03:33.263: EIGRP: Neighbor(183.1.123.2) not yet found R1# *Jun 5 14:03:38.263: EIGRP: Received UPDATE on Serial0/0/0 nbr 183.1.123.2 *Jun 5 14:03:38.263: AS 100, Flags 0×1, Seq 14/0 idbQ 0/0 *Jun 5 14:03:38.263: EIGRP: Neighbor(183.1.123.2) not yet found R1# *Jun 5 14:03:43.263: EIGRP: Received UPDATE on Serial0/0/0 nbr 183.1.123.2 *Jun 5 14:03:43.263: AS 100, Flags 0×1, Seq 14/0 idbQ 0/0 *Jun 5 14:03:43.263: EIGRP: Neighbor(183.1.123.2) not yet found R1# *Jun 5 14:03:48.263: EIGRP: Received UPDATE on Serial0/0/0 nbr 183.1.123.2 *Jun 5 14:03:48.263: AS 100, Flags 0×1, Seq 14/0 idbQ 0/0 *Jun 5 14:03:48.263: EIGRP: Neighbor(183.1.123.2) not yet found R1#
R2#show ip eigrp neighbors IP-EIGRP neighbors for process 100 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 1 183.1.123.1 Se0/0/0 161 00:01:09 1 5000 1 0 0 183.1.123.3 Se0/0/0 146 00:14:27 27 200 0 3 IP-EIGRP neighbors for process 1 R2# *Jun 5 14:09:51.940: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 183.1.123.1 (Serial0/0/0) is down: retry limit exceeded R2# *Jun 5 14:10:22.080: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 183.1.123.1 (Serial0/0/0) is up: new adjacency R2#
what could be the problem ?
Thanks,

Bookmark this post:These icons link to social bookmarking sites where readers can share and discover new web pages.